Nokia 1200 Flash PPM -- APESS!!!

Discussion in 'Nokia Hardware' started by oxphonez, Jun 30, 2008.

Thread Status:
Not open for further replies.
  1. oxphonez

    oxphonez Moderator Moderator

    Messages:
    752
    Likes Received:
    633
    Trophy Points:
    103
    Waduh,... 1000:1 ya ?
    Maksud pengin upgrade bahasa Nokia 1200 v5.06 dan cuman PPM aja yang diproses, jhe... :mad:
    Proses selesai... lah kok ga local mode lagi..
    terus di "Check" lagi deh... weladalah... jadi Unknown Ch!p !!!

    Rehot sudah... apa masih bisa kalo di reball?
    Nyari IC Flash gantinya ini...nih yang repot... rada baru kan tipe 1200 itu?
     
  2. gone_bdg

    gone_bdg Super Moderators Super Moderator

    Messages:
    1,859
    Likes Received:
    3,439
    Trophy Points:
    0

    :confused::eek::confused: WALAH ... QO BISA BEGITU BOS ?
    DI FLASH PAKE APA, PROSESNYA LANCAR GA ?
    SUDAH COBA REMOVE BSI CAPASITOR BOS ?
     
  3. oxphonez

    oxphonez Moderator Moderator

    Messages:
    752
    Likes Received:
    633
    Trophy Points:
    103
    Ya justru bisa begitu :D
    Pake UFSx kan paling aman tuh...
    BSI? Lawong disananya udah jelas Flash Ch!p Unknown, boss...
    Berarti bisa boot normal 'kan?
    BTW.Thanks. Another suggestions, please.... :D
     
  4. gone_bdg

    gone_bdg Super Moderators Super Moderator

    Messages:
    1,859
    Likes Received:
    3,439
    Trophy Points:
    0
    :pound: HE3X MAKSUDNYA SEBELUM ITU PONSEL JADI "UNKNOWN CHIP" ... APA UDA COBA BSI SOLUTION ???
    SAYA PERNAH DAPET KASUS N1200 YG SUSAH DINYALAIN, DAN QLO SUDAH NYALA LALU DIMATIIN KEMUDIAN DINYALAIN LAGI GA BISA .... NAH BEGITU SAYA CHECK DI UFS DCTxBB5 ... PROSES CHECK LANCAR, NAMUN SAAT PROSES INFO GA MAU MASUK LOCAL MODE KEMUDIAN SAYA ULANG PROSES INFO SAMBIUL PENCET KEY POWER-ON DAN AKHIRNYA MAU MASUK LOCAL MODE DAN INFORMASIPUN TERBACA SEMUA.
    LALU SY FLASH UP-GRADE KE
    MCU Sw: V 5.23 10-03-08 RH-99 (c) NMP
    PPM Sw: V 5.23 10-03-08 RH-99 (c) NMP MD
    DIAKHIRI DGN FULL UI SETTING

    TEST RUNNING TETEP AJA SUSAH NYALA ...
    LALU SY REMOVE KUTU2X BSI-NYA DAN DUAR!!! ..... MAU NYALA NORMAL TU PONSEL, DAN MAU MASUK DENGAN LANCAR KE LOCAL MODE.
    BEGITU BOS .....

    NAH KASUS BOS SENDIRI SEBENARNYA GEMANA QO SAMPAI "UNKNOWN CHIP" AND THEN COBA REHOT FLASH IC JUGA TETEP? :confused:
    (SETAHU SY QLO UDA KELUAR LOG INFO MACEM BEGITU ... YA MUSTI REBALL OR GANTI IC FLASH ATUH....) :D
     
  5. om_yozz

    om_yozz New Member

    Messages:
    15
    Likes Received:
    15
    Trophy Points:
    0
    kutu2 BSI mana yang di remove tolong diperjelas ....terima kasih
     
  6. TOTAL PART

    TOTAL PART Administrator Staff Member Administrator

    Messages:
    701
    Likes Received:
    837
    Trophy Points:
    103
    Unknown Ch!p !!!
    pilihan nya cpu dan ic flash.............................
     
  7. ferizona

    ferizona New Member Super Member

    Messages:
    578
    Likes Received:
    682
    Trophy Points:
    0
    Klo kasus gini apanya boz, sdh di rpl tetep, bsa hidup tp hank+blank ga bsa di matiin, msti cabut btre

    Getting MCU ID

    MCU ID: 0x2292
    FLASH ID0: 88280020 <=> ST -> Type not in database Addr0: 0x01000000 - 0x01FFFFFF, SectorSize0: 10
    FLASH ID1: 00010000 <=> Flash -> not used Addr1: 0x02000000 - 0x02FFFFFF, SectorSize1: 0
    First 16 bytes: AD 7E B6 1A 1B BE 0B E2 7D 58 6B E4 DB EE 65 14
    Checking RAM for ALGO...
    Algo is ready...
    Checking FAID calculation...
    P-key nokia module version 01.02
    Done!
    Phone Restarted...
    FILES SET FOR FLASHING:
    MCU Flash file: NONE
    PPM Flash file: NONE
    CNT Flash file: NONE
    ADSP Flash file: NONE
    APE Variant file: NONE
    APE User Flash file: NONE
    Switching to serial...
    Powering the phone...
    Reading...
    MCU SW version: V 4.11
    10-11-07
    RH-99
    (c) NMP
    HW version: 1501
    PCI version:
    UEM version: 1328
    UPP version: 8850
    RFIC version: 0700
    DSP version: P06w45.v41
    LCD version: UNKWN: IDs:
    00:ff:00
    PPM version: V 4.11
    10-11-07
    RH-99
    (c) NMP
    MD
    ADSP SW version: V 4.11\n10-11-07\nRH-99\n(c) NMP\nmd
    Production serial number: DFT873259
    Product code: 0546958
    Module code: 0203402
    Basic production code: 0544418
    Flash code:
    Order number:
    Product specific data:
    Long production SN:
    ATO:
    Default SN type:
    IMEI plain: 356982013371140
    IMEI spare to net: 3A 65 89 02 31 73 11 04
    IMEI SV to net: 33 65 89 02 31 73 11 44 F3
    Master Code: 3036524622
    Phone type: RH-99, Software version: 4.11, Language Pack: MD
    User code: ÿ#

    Block 1:
    Lock 1: OPEN Lock 2: OPEN Lock 3: OPEN Lock 4: OPEN Lock 5: OPEN
    Block 2:
    Lock 1: OPEN Lock 2: OPEN Lock 3: OPEN Lock 4: OPEN Lock 5: OPEN
    Block 3:
    Lock 1: OPEN Lock 2: OPEN Lock 3: OPEN Lock 4: OPEN Lock 5: OPEN
    Block 4:
    Lock 1: OPEN Lock 2: OPEN Lock 3: OPEN Lock 4: OPEN Lock 5: OPEN
    Block 5:
    Lock 1: OPEN Lock 2: OPEN Lock 3: OPEN Lock 4: OPEN Lock 5: OPEN
    Block 6:
    Lock 1: OPEN Lock 2: OPEN Lock 3: OPEN Lock 4: OPEN Lock 5: OPEN
    Block 7:
    Lock 1: OPEN Lock 2: OPEN Lock 3: OPEN Lock 4: OPEN Lock 5: OPEN

    Searching for saved ini...
    Checking for file C:\Program Files\ODEON\JAF\JAF_RH-99.ini
    FILES SET FOR FLASHING:
    MCU Flash file: C:\Program Files\Nokia\Phoenix\Products\RH-99\rh99_04.110
    PPM Flash file: C:\Program Files\Nokia\Phoenix\Products\RH-99\rh99_04.11md
    CNT Flash file: C:\Program Files\Nokia\Phoenix\Products\RH-99\rh990_nai4.11md
    ADSP Flash file: NONE
    APE Variant file: NONE
    APE User Flash file: NONE
    Languages in ppm: English,Filipino,Vietnamase
    Done!

    Error loading cbus loader...
    Setting local mode...
    Reading IMEI...
    Reading IMEI data...
    IMEI data corrupt...
     
  8. ferizona

    ferizona New Member Super Member

    Messages:
    578
    Likes Received:
    682
    Trophy Points:
    0
    hp dah kelar trnyta gnti lcd sembuh.
    sedikit info: klo rusak akibat software, di software lg aza boz, biar bisa konek coba remove 2 resistor dan capasitor dkt con-batre. full erase lalu flash ulang, mcu-ppm-cnt, write pm, init simlock, ful factory
     
  9. oxphonez

    oxphonez Moderator Moderator

    Messages:
    752
    Likes Received:
    633
    Trophy Points:
    103
    Itu hape bisa konek dan bisa di boot normal... kok :confused:
    Sorry ga ada LOG-nya... Cuma pas detek flash ic.......... harusnya kan merek dan tipe flash ic...
    Nah kedua info tesb berubah menjadi Unknown Ch!p!!! Padahal tuh hape ga pernah nonton
    film horor :eek:

    Pokoke ya, begitu itu...
    Sudah saya reball.... tetep...
    Ternyata harus beli flash ic baru, kayaknya
    Terus si empunya hape minta di cancel aja soalnya bahasa arabnya ga ada...
    waduh bener-bener kerja tanpa imbalan plus keluar duit lagi capeee deh :frusty:

    Ya, udah ndak apa2 itung2 bersihin rejeki, kalee... mudah2an :eek:
     
  10. dj_bedhol

    dj_bedhol Moderator Moderator

    Messages:
    374
    Likes Received:
    339
    Trophy Points:
    73
    Haram...sefeser ana tak untung.....:D
     
  11. oxphonez

    oxphonez Moderator Moderator

    Messages:
    752
    Likes Received:
    633
    Trophy Points:
    103
    saya tidak terlalu memusingkan masalah materi boss, yang penting mah bahagia dunia akhirat... itu aja :D
    walaupun cari duit susah yang penting bawa hepi... ga dapat duit bukan rejeki dapat duit ya amanah tho boss? :)
    ya itung2 buat gantiin kalo pas lagi buka hape ada aja yang ilang :D terutama baut... bleh! tombol volume
    nah yang bikin pusing adalah chasing belakang hape suka ilang.... ya di omelin ini itu lah :D sabaaar....

    sekarang kalo ada temen yang ninggal hape gw suruh yang gampang lepas dari hape
    Chasing belakang, Batery, Sim, Memory Eksternal.... dibawa aja, wah kadang hape kesana kesini cuman ada
    tulang dan pcb terus lcd,... sudah itu aja :D
     
  12. ferizona

    ferizona New Member Super Member

    Messages:
    578
    Likes Received:
    682
    Trophy Points:
    0
    saran gone_bdg dah di coba blm boz,
    soalnya itu solusi biar hp bsa masuk local mode
     
  13. hswik

    hswik New Member

    Messages:
    62
    Likes Received:
    34
    Trophy Points:
    0
    Dicoba Aja BOSs....Siapa TAu BIsa Ngurangi APES-nya...
    Kalau belum bisa.... yaa baru namanya bersihin rejeki.

    Kalau Ane BOS Susah cari Duit susaaaah HEPI-nya....MAklum dikejar setoran.....Denger telepon berdering dari kawan mau ngasi kerjaan.....KAGET..
     
  14. djawir_cell

    djawir_cell Administrator Staff Member Administrator

    Messages:
    535
    Likes Received:
    2,112
    Trophy Points:
    103
    pakai ufs ya ?? cek FIA nya bos emang ufs sering bgt gara2 fia eror bikin salah penanganan.

    cobain dulu pakai box lain kalo pakai box lain ic flash kedetek perbaiki FIA nya


    thanks
     
  15. gone_bdg

    gone_bdg Super Moderators Super Moderator

    Messages:
    1,859
    Likes Received:
    3,439
    Trophy Points:
    0
    Ikutan nimbrung lagi ..... MOHON MAAF SEBELUMNYA KEPADA BOS MODERATOR DAN THREAD STARTER
    BILA POSTING SAYA INI RADA OOT ....

    Pernah ga ... ada yg ngalamin N1200 "GOKIL" ato ponsel2x "GOKIL" lainnya ???
    Seperti sekilas kisah dibawah ini ....

    1 : N1200 Normal senormal-normalnya .....l (kata sang user yg kbetulan temen sendiri)
    2: tiba2x sulit dinyalakan
    3 : gak bisa dinyalakan !
    4 : okeh ... saya cek dulu pake UFS .... baru pencet check ... DUAR !!! nyala lagi ponselnya .. LOGnya NORMAL
    5 : proses info & Rd PM (backup) lancar ....
    6 : proses Wr PM (update) lancar ....
    7 : Disconnect .. test running ... walah gak mau nyala2x !!!
    8 : Usernya (temen yg hanya khusus jualan ponsel) bilang ... "Bos ...dibuka aja conector LCDnya trus pasang lagi, Ntar juga Nyala !"
    9 : sambil ketawa Sy komentar ... "Loh qo bisa gitu Bos, apa hubungannya dengan connector LCD ??? "
    10 : User Bilang ... "Gak tau atuh ... Sy taunya jual doank hehehehe .... tapi kmaren, sbelum gw bw kesini gw iseng buka bentar trus pasang lagi coz bingung ga ngerti apa2x ... Eh coba nyalain ...langsung nyala tuh ponsel, eh qlo dimatiin ga mau nyala lagi....maleus bongkar lagi mah"
    11: masih sambil ketawa ... Saya bongkar hp sambil perhatikan mesinnya .......mulus,bagus ga ada yg gemanaaaa gituuuu, trus iseng OOT buka connector LCD bentar ... trus pasang lgi.
    12. ponsel dipasang lagi berikut batere& simcard dan pencet tombol power ON ... lalu DUAR !!! NYALA PONSELNYA ..... :D :D :D
    13. matiin lagi ....nyalain lagi ....matiin lagi ...nyalain lagi ...sampe 6X normal2x aza ....
    14. user yg ngeliatin Sy sambil senyum-senyum bilang ... "uda normal tuh... berapa ongkos flasingnya ?" (cuman WrPM doank)
    15. karena masih heran dgn apa yg baru terjadi ... saya jawab " Ah 25rb aja Bos ... lagian ANEH NEH PONSEL ... he3x"
    16. HAPPY ENDING .... temen saya itu ga pernah ngeluh apa2x soal ponsel tsb .... ;)

    APA HUBUNGAN CONNECTOR PONSEL DENGAN POWER_ON OR BOOT PROCESS PONSEL N1200 ???

    SEKALI LAGI MOHON MAAF QLO SAYA BER-OOT OOT DISINI BOS MODERATOR ......

    COZ TAK JARANG ... BAGI KITA YG BERGELUT DI PERBAIKAN PONSEL MENGALAMI KEJADIAN, ANOMALI , KASUS "ANEH" ATAU MEMBINGUNGKAN SEKALIGUS MENYEDIHKAN JUGA MENGGEMBIRAKAN SAAT "BERCANDA" DENGAN PONSEL2X.

    SEMUA ITU HANYA KARENA ILMU DAN PENGETAHUAN MEMANG TIDAK ADA BATASNYA....SEMENTARA KITA SEBAGAI MANUSIA SERBA TERBATAS ...... JADI SERING MERASA KEANEHAN ....

    SEKALI LAGI MOHON MAAF QLO OOT ....
    C-YA :D
     
  16. fabregas

    fabregas New Member

    Messages:
    87
    Likes Received:
    7
    Trophy Points:
    0

    sm bos wa jg pernah gitu
    wa denger2 sich hrs gnti cpu bos coz cpunya lemah
    tp wa belom coba
    bis lg kereee sich
    :tea::tea:
     
  17. twentyonecell

    twentyonecell Well-Known Member

    Messages:
    315
    Likes Received:
    1,194
    Trophy Points:
    103
    blon tentu ic flash nya rusak ada beberapa hp ada tulisan unknown chip tapi pake flasher jaff bisa booting dan normal




    jaff blm mampu write rpl 1200,1208 yg mampu solusi cuman UB:thumb::thumb:
     
Thread Status:
Not open for further replies.

Share This Page