All Nokia Mobile Phones Convert

Discussion in 'Nokia Hardware' started by evergreen, Apr 27, 2007.

  1. evergreen

    evergreen New Member

    Messages:
    169
    Likes Received:
    467
    Trophy Points:
    0
    All Nokia Mobile Phones Convert


    6010 to 3530

    1. Back up rpl
    2. change flash i.c, 3510i or 3530 flash i.c,then
    3. add a ram to it
    4. flash it to 3510i,,use rh9 v5.35 flash file
    5. change the 3 filters the 850/1900 mhz rx and 1900 mhz tx filter,
    6. put a jumper from uem to pa
    7. write pm
    8. unlock

    3595 to 3530

    1. Flash it to 3530
    2. change 2 filters
    3. write pm
    4. unlock

    6030b to 6030

    1. Change the rx filter 6030b got it any other phone(nokia 3100)
    2. Full flash with 6030 files(Mcu+ppm+cnt)
    3. Write a good pm
    4. unlock

    8801 to 8800

    1. Change Rx And TX filters
    2. write with file 8800_rm13_short.pm

    2651 to 2650


    1. Change filters shown in the picture u can use filters from nokia 3100
    2. Full flash with 2650 files(Mcu,ppm,cnt)
    3. Write a good pm
    4. unlock

    6103b to 6103

    No software modification is required
    (6103b supports 900mhz)

    change 2 filters
    then write 6103 PM
    unlock

    Convert 1110 to 1600

    Convert Nokia 1110 (RH-70) to 1600 (RH-64) (display)

    Replace the display module from 1110 with coloured module from 1600.

    Flash the phone with 1600 flash files and make full factory reset.

    Its not neccessary to flash the phone with 1600 flash files,

    if you don't have flash equipment!

    But then the display will still show no different colours

    1600b to 1600

    1. change 2 filters
    2. flash it to 1600 rh-64 firmware
    3. load 1600pm files
    4. unlock
    contd...
     
    finacell, djbrekele and jankiamreli like this.
  2. evergreen

    evergreen New Member

    Messages:
    169
    Likes Received:
    467
    Trophy Points:
    0
    3650 to 3660

    1. back up rpl
    2. change UPP V2.4 to UPP V3.2
    3. flash to 3660 V5.08
    4. change uem
    5. write special rpl file for 3660
    6. write pm
    7. unlock
    8. replace 3650 keypad to 3660
     
    finacell and jankiamreli like this.
  3. evergreen

    evergreen New Member

    Messages:
    169
    Likes Received:
    467
    Trophy Points:
    0
    2600b to 2600

    1. Flash it to 2600
    2. Change filters
    3. write pm
    4. unlock

    6310 color
    1. Backup rpl
    2. Change flash ic into K5U64418TM.
    3. Flash mcu, ppm and cnt using 8910i flashes.
    4. Write .backup rpl
    5. write pm from 8910i,
    6. unlock
    7. Change lcd into 3510i

    increase backlight( change leds )

    "this is not recommended, its just an additional knowledge"
     
    finacell and jankiamreli like this.
  4. evergreen

    evergreen New Member

    Messages:
    169
    Likes Received:
    467
    Trophy Points:
    0
    3600 to 3650

    1. Flash the phone using 3650 normal flash. ( V3.16 )
    2. change filters
    3. write 3650.pm
    4. unlock

    same procedure with 3620

    3120b to 3100

    1. Flash the phone 3100 but lower than 5.54 (rh19) V4.10 or lower as the version is suitable for converting
    2. change filters
    3. write pm
    4. unlock

    (sometimes no earpiece write pmm)
     
    finacell and jankiamreli like this.
  5. evergreen

    evergreen New Member

    Messages:
    169
    Likes Received:
    467
    Trophy Points:
    0
    1100b to 1100

    1. erase flash
    2. flash with 1100(rh18)
    3. change filters
    4. write pm
    5. unlock
    3200b to 3200

    1. flash the phone with RH 30
    2. replace the filters
    3. write pm
    4. unlock
    5. upload pmm for a 3200 phone

    3220b to 3220

    1. change filters
    2. upload pm
    3. unlock
     
    finacell and jankiamreli like this.
  6. evergreen

    evergreen New Member

    Messages:
    169
    Likes Received:
    467
    Trophy Points:
    0
    a complete guide for 3390 to 3310

    http://rapidshare.com/files/5351998/...nvert.rar.html


    6200 to 6610

    1. flash phone with nhl-4u (6610) mcu + ppm
    2. replace filters
    3. write pm
    4. unlock

    6800a to 6800

    1. flash with 6800a to 6800
    2. replace filters
    3. make jumper near the antenna sw
    4. write pm
    5. unlock

    6061 to 6060

    1. erase whole flash as 6060.
    2. flash ur 6061 with 6060 flash pack "RH-73_dp_46_00_ams_sw_4_10".
    3. replace 2 filters
    4. write pm
    5. unlock
     
    finacell and jankiamreli like this.
  7. evergreen

    evergreen New Member

    Messages:
    169
    Likes Received:
    467
    Trophy Points:
    0
    8390 to 8310

    Jumper resistor is a resistor (not actually a resistor)
    with 0 ohm value, usually colored green with 0 markings.

    Wire can also be use instead, but must not be very thin
    and should be as short as possible. Thin and long wire
    will introduce high inductive reactance and will result
    to weak received signal.


    2. T500 can be taken from 3310 unit. It is located just
    above HAGAR, refer to your service manual to easily
    locate it. Also take note to its pin orientation during
    installation.

    Bypassing Z551 with wires is not recommended,
    this will weaken the receiver sensitivity due to incorrect
    signal phase relationship.


    3. Give special attention when installing VCO, improper
    positioning will result to no network activity

    NgageQda to NgageQd

    1. Erase flash with special erase
    2. flash mcu & ppm to ngageqd
    3. replace filters
    4. write pm
    5. unlock

    6101b to 6101


    No software modification is required coz 6101b is already a GSM tri-band (850_900/1800/1900) but you can also flash it with RM-76 Data Package.

    since phone is tuned to 850 MHz otherwise no network or weak network..

    write pm (6101)
     
    finacell and jankiamreli like this.
  8. evergreen

    evergreen New Member

    Messages:
    169
    Likes Received:
    467
    Trophy Points:
    0
    ****2610b convertion 2610****



    I would like to share you how to convert 2610b RH 87 (010.....imei) to 2610 RH86 TESTED Already :

    1. Please check If your RH 87 is V3.75 (if not just upgrade it flashfiles available at JAF support,

    2. Make Jumpers on 2 filters similar to 1600, 6030.....(refer to sticky post 1600b by port)

    3. Load this Special
    PM

    4. Unlock using JAF 1.98.9


    5. Phone working in Globe/ Smart/ Sun
     
    finacell, lord hans and jankiamreli like this.
  9. ione75

    ione75 Member

    Messages:
    90
    Likes Received:
    12
    Trophy Points:
    18
    tenkyu for alllllllllllll
     
  10. mukeshrajani42

    mukeshrajani42 New Member

    Messages:
    1
    Likes Received:
    0
    Trophy Points:
    0
    6101 sim jumpering digram plese send my id
     
  11. jankiamreli

    jankiamreli New Member

    Messages:
    1
    Likes Received:
    1
    Trophy Points:
    0
    gud post
    thankx for guide how to convert
    many many thankx

    :)
     
    lord hans likes this.
  12. ppicart

    ppicart New Member

    Messages:
    2
    Likes Received:
    0
    Trophy Points:
    0
    need convert 1208b to 1208
    help
     
  13. ppicart

    ppicart New Member

    Messages:
    2
    Likes Received:
    0
    Trophy Points:
    0
    need convert 1208b to 1208
    help
     

Share This Page