Some Important Secret Codes Of China Phones

Discussion in 'Chinese Phone' started by rajon, Nov 2, 2009.

  1. rajon

    rajon New Member Super Member

    Messages:
    1,057
    Likes Received:
    1,420
    Trophy Points:
    0
    Some Important Secret Codes Of China Phones

    __________________________________________________ _______________

    default user code: 1122, 3344, 1234, 5678
    Engineer mode: *#110*01#
    Factory mode: *#987#
    Enable COM port: *#110*01# -> Device -> Set UART -> PS Config -> UART1/115200
    Restore factory settings: *#987*99#
    LCD contrast: *#369#
    software version: *#800#
    software version: *#900#
    set default language: *#0000# Send
    set English language: *#0044# Send
    set English language (new firmware): *#001# Send


    *#0086#, *#0886# set to China
    *#0084#, *#0966# set to Vietnamese
    *#77218114#
    *#19992006#
    *#881188#
    #*94267357#
    *#0084#call


    *#3646633# Sigmatel Engeeniring mode.


    CECT P168/P168+ SCIPHONE I68/I68+ & I9/I9+ Codes

    --------------------------------------------------------------------------

    Engineering Mode: *#3646633#
    Factory Mode: *#66#
    Display IMEI: *#06#
     
  2. rajon

    rajon New Member Super Member

    Messages:
    1,057
    Likes Received:
    1,420
    Trophy Points:
    0
    *#66*# Set Factory Mode CONFIRMED
    *#8375# Show Software Version CONFIRMED
    *#1234# A2DP ACP Mode CONFIRMED
    *#1234# A2DP INT Mode CONFIRMED
    *#0000# + Send : Set Default Language CONFIRMED
    *#0007# + Send : Set Language to Russian CONFIRMED
    *#0033# + Send : Set Language to French CONFIRMED
    *#0034# + Send : Set Language to Spanish CONFIRMED
    *#0039# + Send : Set Language to Italian CONFIRMED
    *#0044# + Send : Set Language to English CONFIRMED
    *#0049# + Send : Set Language to German CONFIRMED
    *#0066# + Send : Set Language to Thai CONFIRMED
    *#0084# + Send : Set Language to Vietnamese CONFIRMED
    *#0966# + Send : Set Language to Arabic CONFIRMED
    CHINESE MODELS:
    default user code: 1122, 3344, 1234, 5678
    Engineer mode: *#110*01#
    Factory mode: *#987#
    Enable COM port: *#110*01# -> Device -> Set UART -> PS Config -> UART1/115200
    Restore factory settings: *#987*99#
    LCD contrast: *#369#
    software version: *#800#
    software version: *#900#
    set default language: *#0000# Send
    set English language: *#0044# Send
    set English language (new firmware): *#001# Send also
    ==========
    Service codes BenQ:
    software version: *#300#
    test mode: *#302*20040615#
    Service codes Pantech:
    software version: *01763*79837#
    service menu: *01763*476#
    reset defaults (phone/user code reset to default): *01763*737381#
    Service codes 3xx, 5xx:
    software version: *#79#
    software version: *#837#
    Service codes VK200, VK2000, VK2010, VK2020, VK4000:
    software version: *#79#
    service menu: *#9998*8336# (hold #)
    reset defaults (phone/user code reset to default): *#9998*7328# (hold #)
    Service codes LG:
    software version: 2945#*#
    Service codes Sony-Ericsson:
    J100 software version: #82#
    Service codes Fly:
    2040(i) reset defaults: *#987*99# Send
    MX200 reset defaults: *#987*99# Send
    MX200 software version: *#900# Send
    SL300m reset defaults: *#987*99# Send
    SL300m software version: *#900# Send
    SL500m reset defaults: *#987*99# Send
    SL500m software version: *#900# Send
    MP500 reset defaults: *#987*99# Send
    MP500 software version: *#900# Send
    Set language to English: *#0044#
    Set language to Russian: *#0007#
    Service codes Konka:
    C926 software version: *320# Send
    C926 set default language: *#0000# Send
    C926 set English language: *#0044# Send
    Service codes GStar:
    GM208 (Chinese Nokea 6230+) engineering menu: *#66*#
    Set language to English: *#0044#
    Set language to Russian: *#0007#
    Service codes Motorola:
    Motofone F3 software version: **9999* Send
    C113, C114, C115, C115i, C116, C117, C118 software version: #02#*
    C138, C139, C140 software version: #02#*
    C155, C156, C157 software version: #02#*
    C257, C261 software version: #02#*
    V171, V172, V173 software version: #02#*
    V175, V176, V176 software version: #02#*
    C168, W220 software version: *#**837#
    W208, W375 software version: #02#*
    ZTE Mobile1- *938*737381#
    2- PHONE WILL DIPLAYED DONE
    3- POWER OFF YOUR PHONE AND POWER ON AGAIN
    alcatelE205
    unlocking phone code,only press***847# without simcard
    E900 software version: *#5002*8376263#
    E900 full reset: *2767*3855#
    Service codes Spice:
    S404 enable COM port: *#42253646633# -> Device -> Set UART -> PS -> UART1/115200
    S410 engineer mode: *#3646633#
    S900 software version: *#8375#
    S900 serial no: *#33778#
    Service codes Philips:
    S200 enable COM port: *#3338913# -> Device -> Set UART -> PS -> UART1/115200
    Service codes "Chinese" models:
    default user code: 1122, 3344, 1234, 5678
    Engineer mode: *#110*01#
    Factory mode: *#987#
    Enable COM port: *#110*01# -> Device -> Set UART -> PS Config -> UART1/115200
    Restore factory settings: *#987*99#
    LCD contrast: *#369#
    software version: *#800#
    software version: *#900#
    Service codes BenQ:
    software version: *#300#
    test mode: *#302*20040615#
    Service codes Pantech:
    software version: *01763*79837#
    service menu: *01763*476#
    reset defaults (phone/user code reset to default): *01763*737381#
    Service codes VK-Mobile 3xx, 5xx:
    software version: *#79#
    software version: *#837#
    service menu: *#85*364# (hold #)
    Service codes VK200, VK2000, VK2010, VK2020, VK4000:
    software version: *#79#
    service menu: *#9998*8336# (hold #)
    reset defaults (phone/user code reset to default): *#9998*7328# (hold #)
    Service codes LG:
    software version: 2945#*#
    KG300 NVRAM format: 2945#*# -> menu 15
    Service codes Sony-Ericsson:
    J100 software version: #82#
    Service codes Fly:
    M100 software version: ####0000#
    2040(i) reset defaults: *#987*99# Send
    MX200 reset defaults: *#987*99# Send
    MX200 software version: *#900# Send
    SL300m reset defaults: *#987*99# Send
    SL300m software version: *#900# Send
    SL500m reset defaults: *#987*99# Send
    SL500m software version: *#900# Send
    MP500 reset defaults: *#987*99# Send
    MP500 software version: *#900# Send
    Set language to English: *#0044#
    Set language to Russian: *#0007#
    Service codes Konka:
    C926 software version: *320# Send
    C926 set default language: *#0000# Send
    C926 set English language: *#0044# Send
    Service codes GStar:
    GM208 (Chinese Nokea 6230+) engineering menu: *#66*#
    Set language to English: *#0044#
    Set language to Russian: *#0007#
    Service codes Motofone-F3:
    Motofone F3 software version: **9999* Send
    ***300* Set SIM Pin
    ***310* / ***311* SIM Pin ON | OFF
    ***000* Reset Factory settings
    ***644* Set Voicemail number
    ***260* / ***261* Auto keypad lock ON | OFF
    ***510* / ***511* Voice Prompts ON | OFF
    ***160* / ***161* Restricted Calling (Phonebook only) ON | OFF
    ***200608* Send: software version
    ***200606* Send: software version
    ***200806* Send: flex version
    ***250* / ***251* Keypad tones ON | OFF
    ***470* Select time format
    ***500* /***501* Prepaid Balance Display ON | OFF
    ***520* Change language
    Service codes Motorola:
    C113, C114, C115, C115i, C116, C117, C118 software version: #02#*
    C138, C139, C140 software version: #02#*
    C155, C156, C157 software version: #02#*
    C257, C261 software version: #02#*
    V171, V172, V173 software version: #02#*
    V175, V176, V176 software version: #02#*
    C168, W220 software version: *#**837#
    W208, W375 software version: #02#*
    and "yes"''
    chiniss cord & pin out
    some chinese Mobile Code And Pinouts :::::::::::>>>>>>>>>
    Service codes BenQ:
    software version: *#300#
    test mode: *#302*20040615#
    Service codes Pantech:
    software version: *01763*79837#
    service menu: *01763*476#
    reset defaults (phone/user code reset to default): *01763*737381#
    Service codes 3xx, 5xx:
    software version: *#79#
    software version: *#837#
    Service codes VK200, VK2000, VK2010, VK2020, VK4000:
    software version: *#79#
    service menu: *#9998*8336# (hold #)
    reset defaults (phone/user code reset to default): *#9998*7328# (hold #)
    Service codes LG:
    software version: 2945#*#
    Service codes Sony-Ericsson:
    J100 software version: #82#
    Service codes Fly:
    2040(i) reset defaults: *#987*99# Send
    MX200 reset defaults: *#987*99# Send
    MX200 software version: *#900# Send
    SL300m reset defaults: *#987*99# Send
    SL300m software version: *#900# Send
    SL500m reset defaults: *#987*99# Send
    SL500m software version: *#900# Send
    MP500 reset defaults: *#987*99# Send
    MP500 software version: *#900# Send
    Set language to English: *#0044#
    Set language to Russian: *#0007#
    Service codes Konka:
    C926 software version: *320# Send
    C926 set default language: *#0000# Send
    C926 set English language: *#0044# Send
    Service codes GStar:
    GM208 (Chinese Nokea 6230+) engineering menu: *#66*#
    Set language to English: *#0044#
    Set language to Russian: *#0007#
    Service codes Motorola:
    Motofone F3 software version: **9999* Send
    C113, C114, C115, C115i, C116, C117, C118 software version: #02#*
    C138, C139, C140 software version: #02#*
    C155, C156, C157 software version: #02#*
    C257, C261 software version: #02#*
    V171, V172, V173 software version: #02#*
    V175, V176, V176 software version: #02#*
    C168, W220 software version: *#**837#
    W208, W375 software version: #02#*
    ZTE Mobile1- *938*737381#
    2- PHONE WILL DIPLAYED DONE
    3- POWER OFF YOUR PHONE AND POWER ON AGAIN
    alcatelE205
    unlocking phone code,only press***847# without simcard
    E900 software version: *#5002*8376263#
    E900 full reset: *2767*3855#
    Service codes Spice:
    S404 enable COM port: *#42253646633# -> Device -> Set UART -> PS -> UART1/115200
    S410 engineer mode: *#3646633#
    S900 software version: *#8375#
    S900 serial no: *#33778#
    Service codes Philips:
    S200 enable COM port: *#3338913# -> Device -> Set UART -> PS -> UART1/115200
    Service codes "Chinese" models:
    default user code: 1122, 3344, 1234, 5678
    Engineer mode: *#110*01#
    Factory mode: *#987#
    Enable COM port: *#110*01# -> Device -> Set UART -> PS Config -> UART1/115200
    Restore factory settings: *#987*99#
    LCD contrast: *#369#
    software version: *#800#
    software version: *#900#
    Service codes BenQ:
    software version: *#300#
    test mode: *#302*20040615#
    Service codes Pantech:
    software version: *01763*79837#
    service menu: *01763*476#
    reset defaults (phone/user code reset to default): *01763*737381#
    Service codes VK-Mobile 3xx, 5xx:
    software version: *#79#
    software version: *#837#
    service menu: *#85*364# (hold #)
    Service codes VK200, VK2000, VK2010, VK2020, VK4000:
    software version: *#79#
    service menu: *#9998*8336# (hold #)
    reset defaults (phone/user code reset to default): *#9998*7328# (hold #)
    Service codes LG:
    software version: 2945#*#
    KG300 NVRAM format: 2945#*# -> menu 15
    Service codes Sony-Ericsson:
    J100 software version: #82#
    Service codes Fly:
    M100 software version: ####0000#
    2040(i) reset defaults: *#987*99# Send
    MX200 reset defaults: *#987*99# Send
    MX200 software version: *#900# Send
    SL300m reset defaults: *#987*99# Send
    SL300m software version: *#900# Send
    SL500m reset defaults: *#987*99# Send
    SL500m software version: *#900# Send
    MP500 reset defaults: *#987*99# Send
    MP500 software version: *#900# Send
    Set language to English: *#0044#
    Set language to Russian: *#0007#
    Service codes Konka:
    C926 software version: *320# Send
    C926 set default language: *#0000# Send
    C926 set English language: *#0044# Send
    Service codes GStar:
    GM208 (Chinese Nokea 6230+) engineering menu: *#66*#
    Set language to English: *#0044#
    Set language to Russian: *#0007#
    Service codes Motofone-F3:
     
  3. rajon

    rajon New Member Super Member

    Messages:
    1,057
    Likes Received:
    1,420
    Trophy Points:
    0
    Service codes ZTE:
    A35 software version: *983*7469#
    Service codes Panasonic:
    X500 software version: *#9999#
    X500 software version: #02#*
    X500 system reset: **0102#
    Service codes Alcatel:
    C820, C825, C700, C701, C707, C717, Elle-N3 set language to English: *#0044#
    C820, C825, C700, C701, C707, C717, Elle-N3 set language to Russian: *#0007#
    C820, C825, C700, C701, C707, C717, Elle-N3 set language to French: *#0033#
    E101, E207 software version: *#4837*#
    E101, E207 auto call test: *#2255*#
    E101, E207 memory status: *#6362*#
    E101, E207 reset menu: *#7378*#
    S520 factory mode: *#3228#
    S520 engineer mode: *#364463#
    S520 software version: *#837#
    S520 auto test: *#2886#
    S520 clean test records: *#3872#
    S520 restore default settings: *#73738#
    S520 something unknown: *#200709*01#
    Service codes Motorola CDMA: w150, w150i, w170, w170c, w200, w210, w355:

    Set English language:
    1. Menu
    2. Down 7 times, Right soft button
    3. Down 3 times, Right soft button
    4. Down 1 times, Right soft button
    5. Down 4 times, Right soft button
    6. select language now

    Service codes Samsung:
    E900 software version: *#5002*8376263#
    E900 full reset: *2767*3855#
    Service codes Spice:
    S404 enable COM port: *#42253646633# -> Device -> Set UART -> PS -> UART1/115200
    S410 enable COM port: *#3646633# -> Device -> Set UART -> PS -> UART1/115200
    S410 engineer mode: *#3646633#
    S900 software version: *#8375#
    S900 serial no: *#33778#
    Service codes Philips:
    S200 enable COM port: *#3338913# -> Device -> Set UART -> PS -> UART1/115200
    Service codes Virgin-Lobster-544:
    Enable COM port: *#110*01# -> Device -> Set UART -> PS Config -> UART1/115200
    Service codes "Chinese" models:
    default user code: 1122, 3344, 1234, 5678
    Engineer mode: *#110*01#
    Factory mode: *#987#
    Enable COM port: *#110*01# -> Device -> Set UART -> PS Config -> UART1/115200
    Restore factory settings: *#987*99#
    LCD contrast: *#369#
    software version: *#800#
    software version: *#900#
    set default language: *#0000# Send
    set English language: *#0044# Send
    set English language: *#0001# Send
    set English language: *#001# Send
    Service codes BenQ:
    software version: *#300#
    test mode: *#302*20040615#
    Service codes Pantech:
    software version: *01763*79837#
    service menu: *01763*476#
    reset defaults (phone/user code reset to default value 1234): *01763*737381#
    Service codes VK-Mobile 3xx, 5xx:
    software version: *#79#
    software version: *#837#
    service menu: *#85*364# (hold #)
    Service codes VK200, VK2000, VK2010, VK2020, VK4000:
    software version: *#79#
    service menu: *#9998*8336# (hold #)
    enable hidden languages: *#9998*8336# (hold #) -> change Region
    reset defaults (phone/user code reset to default): *#9998*7328# (hold #)
    Service codes LG:
    default security code: 0000
    clear user code/user lock: 2945#*# -> Factory Reset
    software version: 2945#*# -> S/W version
    KG300 NVRAM format: 2945#*# -> menu 15
    more information: 2945#*45#
    simlock menu: 2945#*20001#>/li>
    Service codes Sony-Ericsson:
    J100 software version: #82#
    K200i, K205i, K220i service info: *** (w/o sim)
    Service codes Fly:
    M90 reset user code: *2100#
    M100 software version: ####0000#
    M110 reset user code: *2100#
    2040(i) reset defaults: *#987*99# Send
    MX200 reset defaults: *#987*99# Send
    MX200 software version: *#900# Send
    SL300m reset defaults: *#987*99# Send
    SL300m software version: *#900# Send
    SL500m reset defaults: *#987*99# Send
    SL500m software version: *#900# Send
    MP500 reset defaults: *#987*99# Send
    MP500 software version: *#900# Send
    Set language to English: *#0044#
    Set language to Russian: *#0007#
    Enable COM port: *#110*01# -> Device -> Set UART -> PS Config -> UART1/115200
    Service codes Konka:
    C926 software version: *320# Send
    C926 set default language: *#0000# Send
    C926 set English language: *#0044# Send
    Service codes GStar:
    GM208 (Chinese Nokea 6230+) engineering menu: *#66*#
    Set language to English: *#0044#
    Set language to Russian: *#0007#
    Service codes Motofone-F3:
    Motofone F3 software version: **9999* Send
    ***300* Set SIM Pin
    ***310* / ***311* SIM Pin ON | OFF
    ***000* Reset Factory settings
    ***644* Set Voicemail number
    ***260* / ***261* Auto keypad lock ON | OFF
    ***510* / ***511* Voice Prompts ON | OFF
    ***160* / ***161* Restricted Calling (Phonebook only) ON | OFF
    ***200608* Send: software version
    ***200606* Send: software version
    ***200806* Send: flex version
    ***250* / ***251* Keypad tones ON | OFF
    ***470* Select time format
    ***500* /***501* Prepaid Balance Display ON | OFF
    ***520* Change language
    Service codes Motorola:
    C113, C114, C115, C115i, C116, C117, C118, C122 software version: #02#*
    C113, C114, C115, C115i, C116, C117, C118, C122 reset defaults: **0102#
    C138, C139, C140 software version: #02#*
    C138, C139, C140 reset defaults: **0102#
    C155, C156, C157 software version: #02#*
    C155, C156, C157 reset defaults: **0102#
    C257, C261 software version: #02#*
    V171, V172, V173 software version: #02#*
    V171, V172, V173 reset defaults: **0102#
    V175, V176, V176 software version: #02#*
    C168, C168i, W220 software version: *#**837#
    C168, C168i, W220 master reset: *#**367628# Send
    C168, C168i, W220 E2p reset: *#**778337# Send
    W205, W208, W375 software version: #02#*
     
  4. deved

    deved New Member

    Messages:
    2
    Likes Received:
    0
    Trophy Points:
    0
    Dear Friends

    I have made some changes in Sigmatel (t99i) using this code *#3646633# Sigmatel Engeeniring mode. Now unable to get it on. how to get the same on in default mode with default settings. Please help to get it on.
     

Share This Page