Need help for UFS3

Discussion in 'UFS/N-Box/HWK' started by mehran, Dec 8, 2006.

  1. mehran

    mehran New Member

    Messages:
    2
    Likes Received:
    0
    Trophy Points:
    0
    I have a cloned UFS3 box with HWK that was working with ufs suite 3.03.
    I used a software to upgrade to 2.6.7 and after that the DCTx sayes BOX_AUTH_ERROR and others saying "Selected Device, not Compatible with Software".
    I tried every firmware that I could find and also reverted to 2.5 and used "UFS3 Tools 2.69b" but results are same.
    Seems they are working only for original boxes.
    with DCTx Tools 1.3j when I push connect it only beeps after checking the box and shows nothing.

    I checked other boxes atmega on the box(with changing the ft232's serial)it's working.so it's the firmware problem inside atmega.

    With "HWK Replacer V 3.03.001" "
    Code:
    Updating started...
    > Device: UFS3 SarasSoft, S/N: 71*** - opened.
    > Entered to BOOT...      >>> 62  CF
    > Features: 00000001  
    > Section 1F: 00C7  
    > SN = 71*** (0x11***)
    > UFS fw CRC: 0x5FA6401A
    > Please update your...
    > Operation aborted
    > Device closed.
    and says
    Code:
    You need update your UFS before to continue
    You can see this message only if:
    - Checksum of your UFS firmware is not correct
    - UFS firmware was patched
    - Very Old firmware
    - ...(i am very lazy to make more tests)
    
    PS: you can use UFS3Tool to update your box
    Any HELP,
    Thanks in advance.
     
  2. bintang1309

    bintang1309 New Member

    Messages:
    282
    Likes Received:
    169
    Trophy Points:
    0
    bahasa gaul aza , jgn bahasa inggris...............
     
  3. admin

    admin Administrator Staff Member Administrator

    Messages:
    2,397
    Likes Received:
    2,623
    Trophy Points:
    123
    u need ufstools and rewrite firmware & eeprom

    @bintang1309
    dia gak bakalan isa pake bahasa gaul wong bukan dari indonesia
     
  4. oxphonez

    oxphonez Moderator Moderator

    Messages:
    752
    Likes Received:
    633
    Trophy Points:
    103
    dari india kali, ya ???
    wah...bisa main tiap ari ke tah mahal :D
     
  5. mehran

    mehran New Member

    Messages:
    2
    Likes Received:
    0
    Trophy Points:
    0
    @djawir
    Thanks for your reply.
    I did and converted to 2.5 but after that when I run "DCTx Tools 1.3j" it only dings and nothing happens!?

    @others
    I can't read your writings. Plz write in english.
     
  6. oxphonez

    oxphonez Moderator Moderator

    Messages:
    752
    Likes Received:
    633
    Trophy Points:
    103
    dia kembali lagi :D
    kirain cuman numpang lewat :D

    @ mehran
    you can visit this site for more information about writing eeprom to your box
    Code:
    http://www.ftdichip.com/Resources/Utilities/MProg2.9_Setup.exe
    have you follow correctly ?
    first uninstall driver, unplug&plug your box. and then install the driver.
    you can download from ftdichip(dot)com. downgrade to 2.5 fix and update.
    if until this step going correctly, now you can update to 2.6. and remember, after
    update you must using newer driver
     
    Last edited by a moderator: Dec 10, 2006
  7. romy

    romy New Member

    Messages:
    28
    Likes Received:
    3
    Trophy Points:
    0
    sorry mehran,pake bahasa indo donk jangan eglish segala,kagak ngarti mah!
     
  8. opick

    opick New Member

    Messages:
    29
    Likes Received:
    21
    Trophy Points:
    0


    wakakakak......bule bo':pound: :pound:
     
  9. oxphonez

    oxphonez Moderator Moderator

    Messages:
    752
    Likes Received:
    633
    Trophy Points:
    103
    piye to, wong takon malah ditakoni :D :D :D
     
  10. agt

    agt New Member

    Messages:
    1
    Likes Received:
    0
    Trophy Points:
    0
    Could any body help, i updated my ufs-5 with Atmega to 2.7. Now I can not find virtual com port in the device manager and therefore i can't connect my ufs-5
     
  11. ug_chaos

    ug_chaos New Member

    Messages:
    11
    Likes Received:
    1
    Trophy Points:
    0
    ga mudeng iki...:confused:
     

Share This Page