Ada apa dengan mcn pro ku ??????????????

Discussion in 'Chinese Phone' started by ashakaas, Apr 21, 2011.

  1. ashakaas

    ashakaas Well-Known Member

    Messages:
    344
    Likes Received:
    345
    Trophy Points:
    73
    Mcnpro Box official version 3.0.6 Released
    Released: March 23, 2011


    • Detection bugs fixed for MTK 6253 / 6268 / 6235
    • Improved USB Scan to be more stable (eg. Spreadtrum no need holding power key)
    • Spreadtrum IMEI read /write function Improved
    • Spreadtrum code read function Improved (Direct from file)
    • Add Spreadtrum cpu factory reset function
    • Add Spreadtrum cpu safe format function (beta)
    • Add Spreadtrum read phonebook function (Direct from file)
    • Add Mstar cpu manual format function
    • Add Mstar cpu auto format function
    • Add automatic repower fucntion for all CPUs (highlight function)
    • Other small report bugs fixed
    melihat hal diatas sepertinya mcn bisa dengan mudah read n flash mtk6253 , tp terxta cuma bisa deteksi rx tx saja , tak bisa read apalagi tulis firmware. coba pake box cpf pro sippppp goyang ngebor...problem slesai. pertanyaan ADA APA DENGAN MCN KU ?????????
    ini log di mcn
    Start Scanning...
    ->..
    Results:
    CPU: MT6253.
    VCC:3,GND:9 12,RXD:7,TXD:6
    [V:3 G:9 12 R:7 T:6] Apply to Box
    [V:3 G:9 12 R:7 T:6] Apply to Box
    Press and Holding Power button now !
    Connecting, wait...
    Phone detected, wait..
    CPU: 6253 Ver: 8A02 Software:8A00
    CPU ID: 00000F00
    General DA
    Initialize Boot7 ...
    Phone not support on this boot, or cpu dead

    ini log cpf pro
    Gnd: 1 4
    Did not find short pins
    Analyzing Rx and Tx...
    MT6253, RX: 6, TX: 7
    Setting...
    Pinouts setting complete!
    Waiting for phone's response,please press Power Waiting for phone's response,please press Power on/off button.
    Connecting...
    Hardware version:8A02
    Software version:8A00
    CPU Type:6253
    Boot downloading complete!
    Flash ID: 0001007E
    Flash type:
    Chip Capacity: 0x01000000
    Baud adjust...complete.
    Flash reading...100%

     
  2. emha

    emha Member

    Messages:
    36
    Likes Received:
    5
    Trophy Points:
    18
    sama bos ane juga pake MCN buat flash IMO G911 cuma bisa deteksi RX TX aja, selanjutnya ...Phone not support on this boot, or cpu dead
    knp ya?
     
  3. nursephone

    nursephone Member

    Messages:
    32
    Likes Received:
    7
    Trophy Points:
    18
    ane aman2 aja bro

    [​IMG]

    coba cek selftest sama upgrade boxya master

    Start Scanning...
    ->.
    Results:
    CPU: MT6253.
    VCC:3,GND:6,RXD:1,TXD:4,BOOT:2
    [V:3 G:2 6 R:1 T:4] Apply to Box
    Comm Error 001:Definitions may be incorrect, to scan again
    Press and Holding Power button now !
    Connecting, wait...
    Phone detected, wait..
    CPU: 6253 Ver: 8A02 SW:8A00
    CPU ID: 00000F00
    Initialize Boot6 ...
    Flash(Nor) Type [AMIC] A82DL3228T
    Flash(Nor) Code 00898903(00000000)
    Flash(Nor) Size 0x01000000 Hex Bytes
    Checking baudĀ”*
    Set Baud:921600 Done.
    Start Reading(Nor)...
    Read Done !
    Time used: 4 mins 14 s
    File Saved: D:\SOFTTWARE HP\MCN\back up mcn\cros gg51 dt


    FORMAT
     

Share This Page