Software Pulsa Tiger Engine
Kiswara

c3-00 lcd

Discussion in 'BB5' started by stroy, May 19, 2011.

  1. stroy

    stroy Active Member

    Messages:
    102
    Likes Received:
    46
    Trophy Points:
    38
    bos ada yg tau jalur lcd nokia c3-00...hpnya blank putih kadang normal......tolong solusinya bosmaster...
     
    eko_ajo likes this.

    Mobile Connection
  2. berkat cell

    berkat cell Moderator Moderator

    Messages:
    3,721
    Likes Received:
    16,850
    Trophy Points:
    123

    lihat trik pengerjaannya pada panduan gambar dibawah::
    lihat komponen pendukung kinerja lcd nya

    khusus teg Vio_lcd dan Vaux_lcd
    [​IMG]
     

    Asisten VRE
    Kiswara Modem
  3. stroy

    stroy Active Member

    Messages:
    102
    Likes Received:
    46
    Trophy Points:
    38
    juno ic lettaknya dimana gan ?apa yg diatasnya kamera?
     
    eko_ajo likes this.
  4. berkat cell

    berkat cell Moderator Moderator

    Messages:
    3,721
    Likes Received:
    16,850
    Trophy Points:
    123
    pengerjaan nya yang ringan dulu gan..!!!
    jangan langsung ke ic juno...!!!
    teg Vio_lcd = 1.8 v dan Vaux_lcd = 2.8 v jika teg ini tidak normal mengakibatkan pemakaian arus ke lcd juga
    terganggu..!! akibatnya kinerja lcd malfunction ( kadang putih-biru )...!!!
     
    eko_ajo likes this.
  5. ansel

    ansel New Member

    Messages:
    57
    Likes Received:
    28
    Trophy Points:
    0
    sama bos saya lagi pusing dgn c3 blank gak kelar2,uda ganti lcd,ganti konector lcd,jalur semua normal,tegangan vio,vaux,normal,semuanya,apanya lagi,
     

    aa-pulsajaya
  6. berkat cell

    berkat cell Moderator Moderator

    Messages:
    3,721
    Likes Received:
    16,850
    Trophy Points:
    123


    pastikan bahwa firmware ponsel nya bagus..??

    cek R2470 dan R2471....rehot atau reball ic juno
    moga berhasil
     
    eko_ajo likes this.
  7. ansel

    ansel New Member

    Messages:
    57
    Likes Received:
    28
    Trophy Points:
    0
    thanks bos,setelah rehot JUNO langsung keluar gambar,asikkkkkkkkkkkkkkkkkkkkkkkk.
     
    eko_ajo likes this.
  8. Kitten

    Kitten Active Member

    Messages:
    65
    Likes Received:
    66
    Trophy Points:
    28
    gambarnya ga keliatn mas?..
     
  9. berkat cell

    berkat cell Moderator Moderator

    Messages:
    3,721
    Likes Received:
    16,850
    Trophy Points:
    123
    good job bro.....jadi buka nota deh...????

    cara/trik jumper nya di up load lagi...silahkan master kitten ...diambil..moga bermanfaat
     

    Attached Files:

    TRIMUR, teckyong, ankwal_cell and 2 others like this.

  10. japhone

    japhone New Member

    Messages:
    3
    Likes Received:
    0
    Trophy Points:
    0
    thank bos....... ijin byedooot elmunya........
     
  11. 4doel

    4doel New Member

    Messages:
    46
    Likes Received:
    6
    Trophy Points:
    0
    klo gw dulu juga sempet pusing 7 keliling, ga taunya connectornya kurang mateng solderannya. . pengal:rock:aman aja, tapi ngomong2 kue pancong kali 'mateng'...
     
  12. jengwa1111

    jengwa1111 New Member

    Messages:
    9
    Likes Received:
    1
    Trophy Points:
    0
    trim's gan
    tp kasus saya blum terpecehkan gan
    kalau tegangan vaux gak keluar apa yg harus di eksekusi gan?
     
  13. berkat cell

    berkat cell Moderator Moderator

    Messages:
    3,721
    Likes Received:
    16,850
    Trophy Points:
    123

    coba cek Capasitor C2401 ( Vaux_lcd ) ada ga nilai nya =100n atau bocor/rusak..??
    jika rusak ganti baru dgn nilai yg sama ( ambil dr kanibalan ponsel yg lain nya )
    atau jumper ke C2218

    buka skema diagramnya...moga berhasil
     
  14. jengwa1111

    jengwa1111 New Member

    Messages:
    9
    Likes Received:
    1
    Trophy Points:
    0
    thank's gan udah saya jumper ke c2218 tp gambar tetap gak keluar
    "vaux"udah keluar
    nb:-kondisi hp __komponen disekitar konektor lcd ilang semua gan dan jalurnya banyak yg rusak sebaggian udah ana sambung dan buat jalur baru serta komponennya saya ganti..hanya saja c3401 dan c2400 gak ana pasang apa pengaruh gan trim's
     
  15. jengwa1111

    jengwa1111 New Member

    Messages:
    9
    Likes Received:
    1
    Trophy Points:
    0
    thank's gan udah saya jumper ke c2218 tp gambar tetap gak keluar
    "vaux"udah keluar
    nb:-kondisi hp __komponen disekitar konektor lcd ilang semua gan dan jalurnya banyak yg rusak sebaggian udah ana sambung dan buat jalur baru serta komponennya saya ganti..hanya saja c2401 dan c2400 gak ana pasang soalnya jalurnya saya kebingungangan pada ngilang semua..apa pengaruh klu "C"nya jika gak dipasang gan ?????
    trim's
    mohon pencerahannya..
     
  16. nampes

    nampes New Member

    Messages:
    254
    Likes Received:
    369
    Trophy Points:
    0
    klau pengaruhnya gk begitu besar dengan catatan di c2401 dan c2400 ada tegangannya(jalurnya terkoneksi ke ic juno) coba dicek pake multitester
     
    jengwa1111 likes this.
  17. jengwa1111

    jengwa1111 New Member

    Messages:
    9
    Likes Received:
    1
    Trophy Points:
    0
    maaf gan biar lebih mantab saya upload gambar mesinnya jalur lcd1.jpg
     
    teckyong likes this.
  18. jengwa1111

    jengwa1111 New Member

    Messages:
    9
    Likes Received:
    1
    Trophy Points:
    0
    tolong pencerahannya gan ..
     
  19. jengwa1111

    jengwa1111 New Member

    Messages:
    9
    Likes Received:
    1
    Trophy Points:
    0
    ini yg sudah saya lakukan:
    -software hp udah tak kasih yg paling tinggi
    -VAUX udah ana ambil dari c2218 dan udah keluar tegangannya
    -konektor lcd baru diganti
    _rehot juno

    mohon bantuannya para master.......
     
  20. jengwa1111

    jengwa1111 New Member

    Messages:
    9
    Likes Received:
    1
    Trophy Points:
    0
    sundul lagi ah...tolong master
     

Share This Page