bb 8520 buka kamera hapus aplikasi lain

Discussion in 'BlackBerry' started by desi_adelia, Oct 2, 2014.

  1. desi_adelia

    desi_adelia New Member

    Messages:
    225
    Likes Received:
    40
    Trophy Points:
    0
    yg uda dilakukn gnti kamera ,jumper di tp 622 ke konektor kamera,,,instal jg nggk jg bisa,,,dilihat pin tp 622 jebol...kerok smpai dpt kuningn gitu jg jumper nggk jg done gan
     
    sendypr likes this.
  2. ariemahendra

    ariemahendra Well-Known Member Super Member

    Messages:
    872
    Likes Received:
    577
    Trophy Points:
    103
    coba ukur nilai hambatan di tiap2 kaki.

    kl nilai hambatan kluar smua/sesuai dgn skema,langkah selanjutnya angkat kaki dikonektor kamera,jika masih g mau coba ganti module,langkah terakhir cek driver kamera
     
    rio ganara likes this.
  3. rio ganara

    rio ganara Moderator Moderator

    Messages:
    3,105
    Likes Received:
    2,216
    Trophy Points:
    123
    sedikit menambah ..


    pastikan tegangan kerja kameranya keluar ... atau coba pinjem tegangan dari CON LCD


    kamera tegangan.
     
    sendypr likes this.
  4. okensie

    okensie Member

    Messages:
    5
    Likes Received:
    1
    Trophy Points:
    13
    pastikan jalur tegangan kerja di pin 4 n 16 keluar,tapi kluarx setelah tegangan perintah yaitu ce ato control enable kluar di testpoint(tp)1708 ada 1,8volt.tapi penting jalur scl n sda bagus, n jalur data juga
     
  5. desi_adelia

    desi_adelia New Member

    Messages:
    225
    Likes Received:
    40
    Trophy Points:
    0
    gabungin ps dan avo buat ukur teg..nya pcd bb nggk da conbat permanen apa main solder ya bos,,,biar bisa aq akurat aq ukur teg dcmera
     
  6. desi_adelia

    desi_adelia New Member

    Messages:
    225
    Likes Received:
    40
    Trophy Points:
    0
    setelah ukur by avo meter setel kalibrasi 10x nilai inpendansi hambatan dalam di 20 kaki kamera ternyata kaki 15 putus diliat skema harus jumper ke dlm kaleng cpu,setelah liat tespoinnya tp 622 bisa sebagai gntinya buat jumper ke kaki 15,tp sayang tp 622 uda jebol tidak ada lg kuningnnya,,,pertanyaan saya master apakah bisa dijumper kan kaki 15 ke tp 1708,atau tp621?
     
  7. rio ganara

    rio ganara Moderator Moderator

    Messages:
    3,105
    Likes Received:
    2,216
    Trophy Points:
    123
    buka skema ... perhatikan jalur di PIN ke 15 ... itu jalur SDA ..


    perhatikan gambar dibawah ... cek jalur, cek resistansi , pastikan OK .. bisa ambil di R617 ..

    Kamer SDA.
     
  8. desi_adelia

    desi_adelia New Member

    Messages:
    225
    Likes Received:
    40
    Trophy Points:
    0
    klu nyolong teg kedalam cpu beresiko klu aq ambil teg v1_8dig dikonektor lcd bsa bos
     
  9. desi_adelia

    desi_adelia New Member

    Messages:
    225
    Likes Received:
    40
    Trophy Points:
    0
    kaki 15 djumper ke c1201 bisa short nggk ya,, karena bongkr kaleng cpu beresiko ,, usernya entr lum dikasitau resikonya
     
  10. desi_adelia

    desi_adelia New Member

    Messages:
    225
    Likes Received:
    40
    Trophy Points:
    0
    ouiya lupa bos pke potong kuku ja y,,,langsung jumper kaki luar no.15 ke r 617 y,,,,,mikir2 ketemu jg caranya
     
  11. desi_adelia

    desi_adelia New Member

    Messages:
    225
    Likes Received:
    40
    Trophy Points:
    0
    jarum avo nya bergerak dikit memang r 617 nilainya kecil x ya,,,,jd aq jumper ja ya ke kaki 15
     
  12. desi_adelia

    desi_adelia New Member

    Messages:
    225
    Likes Received:
    40
    Trophy Points:
    0
    yah memang ngk mujur r 617 jumper ke kaki 15 jd matot hp ,, lepas jumperannya idup lg,,,klu uda begini pinjem teg mn lgi y selain harus bongkar kaki cpu
     
  13. rio ganara

    rio ganara Moderator Moderator

    Messages:
    3,105
    Likes Received:
    2,216
    Trophy Points:
    123
    pastikan bukan GROUND yang disambung ....
     
  14. desi_adelia

    desi_adelia New Member

    Messages:
    225
    Likes Received:
    40
    Trophy Points:
    0
    okudaqjumpertetapjamatot
     
  15. rio ganara

    rio ganara Moderator Moderator

    Messages:
    3,105
    Likes Received:
    2,216
    Trophy Points:
    123
    banyak kemungkinan proses jumperan tidk rapi ..

    coba buka skema .. atau cari perbandingan di mesin yang normal ..

    PIN 15 itu terhubung ke R617 .... pastikan PIN 15 tidak GROUNDING , pastikan TP 622 tidak GROUNDING ..

    setelah lakukan jumper cek resistansi jalur apakah GROUNDING atau tidak ...

    pastikan KAMERA juga OK ...
     
  16. desi_adelia

    desi_adelia New Member

    Messages:
    225
    Likes Received:
    40
    Trophy Points:
    0
    jumperannya dikaki 15 yg diluaR GAN BUKAN DI TP 622 KARENA TP 622 UDA BLONG,, NK DA TIMAH,,, TRUS JUMPER KE R617 SEBELAH KIRI
     
  17. desi_adelia

    desi_adelia New Member

    Messages:
    225
    Likes Received:
    40
    Trophy Points:
    0
    Masih jg matot lepas jumperan idup lg,,,
     
  18. desi_adelia

    desi_adelia New Member

    Messages:
    225
    Likes Received:
    40
    Trophy Points:
    0
    masih ada harapn nggk nie camera y,,,
     
  19. desi_adelia

    desi_adelia New Member

    Messages:
    225
    Likes Received:
    40
    Trophy Points:
    0
    Setelah bongkar cpu ambil ambil kwt jumper lngsung jumper ketitik kakinya cetak pasng lg cpu done lngsung
     

Share This Page